BORA cooktop extraction systems
Modell
Article no.
Price CHF
Product description
Technical data
Operating voltage
230 V / 50 Hz
Power consumption
5.5 W
Fuse protection
5 A inactive, soldered, cannot be replaced by the user
Functional area
0 °C / + 60 °C
Protection category
IP 20
Radio frequency
868 MHz, short range device
SRD
Transmission power (ERP)
max. 25 mW, power class 9
Range
Up to 20 m in an open area
Receiver (H x W x D)
53 x 53 x 31 mm
Transmitter (H x W x D)
55 x 31 x 18 mm
Magnet (H x W x D)
55 x 15 x 18 mm
Spacer plate (H x W x D)
55 x 15 x 5 mm
Scope of delivery
Radio receiver
Radio magnetic switch
Battery CR2032 / 3V
4 spacer plates
Operating instructions
Mounting material
Simultaneous exhaust air operation with heating units
Ambient air dependent heating units (e.g. gas, oil, wood or coal operated heating devices, continuous flow heaters, water heaters) obtain combustion air from the installation room and route the exhaust gases outside via an exhaust gas system (e.g. chimney).
If the cooktop extractor is used in exhaust air operation, the ambient air is taken from the installation room and the neighbouring rooms. Without sufficient supply air, a vacuum will occur.
Toxic gases from the chimney or extraction duct will be pumped back into the living areas. This applies to both ambient air dependent and ambient air independent heating units. The window contact switch guarantees that the cooktop extractor can only be operated in the case of sufficient fresh air supply.
Window contact switch
The BORA window contact switch UFKS ensures sufficient fresh air supply in the kitchen, when operating an extractor device in the immediate vicinity of an ambient air independent heating unit. A sensor in the window casement monitors whether the window is open or closed and sends this information to the recipient via radio which is connected to the home-in interface of the relevant BORA cooktop extractor. In this way, it is ensured that the installed extractor system can only be operated if the window is open. Therefore, the risk of a vacuum in the room is prevented. The BORA window contact switch is suitable for BORA Professional, BORA Classic 2.0, BORA Classic, BORA Basic and BORA Pure. The connection must be carried out by a professional electrician.
Planning note for BORA Pure / X Pure:
Deliveries until 30. 9. 2022: Requires the use of the Home In module PUHIM, can be ordered separately, not included in the scope of delivery.
Deliveries from 1. 10. 2022: Use of the Home In module PUHIM no longer required due to software adaptations.
Downloads
Availability
BORA Universal
BORA control line EC 10 m
Article no.
Price CHF
BORA mains cable EC 10 m
Article no.
Price CHF
BORA ULS base fan
Brief description
Mode of operation
Article no.
Price CHF
BORA shallow silencer USDF
Article no.
Price CHF
BORA round silencer USDR50
Article no.
Price CHF
BORA duct fan ULI
Article no.
Price CHF
BORA external wall fan ULA
Article no.
Price CHF
BORA tiled roof fan ULZ
Article no.
Price CHF
BORA flat roof fan ULF
Article no.
Price CHF
BORA additional duct fan ULIE
Article no.
Price CHF
BORA air cleaning box flexible ULBF (successor ULB1)
Article no.
Price CHF
BORA air cleaning box ULB3X
Article no.
Price CHF
BORA filter set ULB3AS (3 activated carbon filter cartridges)
Article no.
Price CHF
Window contact switch UFKS
Article no.
Price CHF
BORA socket USTJ
Article no.
Price CHF
